Whether you ’re putting in a brand - new door or just supersede assume - out hardware , it ’s wanton to install a new grip and lock on your front door .
Installing a front door handle and lockset is a quick way toadd curb appeal to your home . Before you begin , ensure your door has standard preparation boreholes for a boss / lever tumbler and bolt combination .
This type of preparation is for a door with two sets of boreholes and crossbreeding bores , one on top of the other , 5 - 1/2 inches from center to pore . Both boreholes are 2 - 1/8 inches in diam , with the interbreeding bores measuring 1 inch in diam . The back set measures between 2 - 3/8 and 2 - 3/4 inches from the edge of the room access to the center of the hybridisation bore . The thickness of the door should be between 1 - 3/8 and 1 - 3/4 inches . Be aware of the dimension of your Modern handle so that it match properly on the threshold .
utilise caution when using an galvanizing practice session to instal any screws . It could well strip the screw threads or damage the hardware . Do not tighten the screws too much ; you may always go back later and tighten them .
How to Install a Door Handle and Lock
Supplies Needed
Step-by-Step Directions
Step 1: Install the Latch
Determine whether you want to use a flat , rectangular faceplate or a round private road - in faceplate . ( Many kit amount with both choice . ) If you desire to use a monotonic faceplate but do not have an indent on the edge of your door to fit it over the hybridisation bore , trace the outline of the faceplate with a pencil and make the outline with a public utility tongue so that the wood does n’t splinter . Use a 1 - in chisel to chisel out a rectangle 1/8 - column inch deep ( it must be flush with the door jamb ) , 1 inch wide-cut , and 2 - 1/4 inches tall , center on around the cross drill hole . Once you have an indentation on the edge of your room access , slither the latch into the cross bore with the bevel facing the door jamb and fasten it against the indentation with two myopic screws .
If you favor the smaller round drive - in faceplate , habituate a flathead screwdriver to take away the fuck on the flat faceplate and support plate . add the round ride - in faceplate over the latch and press down to secure . slue the latch and ride - in faceplate into the cross bore with the bevel facing the door jam , and push in until pie-eyed . Use a malleus with a block of Mrs. Henry Wood between it and the latch to gently thump it into stead ( until affluent with the boundary of the door ) without damage the hardware .
Step 2: Install the Outside Handle
If your fresh door care attache case to the door at a spot below the low-spirited borehole ( like ours ) , you may ask to drill another mess to accommodate it . describe up the spindle on the back of the handle with the expansion slot in the door latch , slide any mechanisms up or down as want to fit the handgrip onto the door .
Step 3: Install the Inside Handle
run along up the inside handgrip or lever tumbler so that the screw holes align vertically with the threaded posts on the back of the outside handle . If your inside handle is a lever , verify that the lever is pointing by from the door jamb . Secure with screw . If your international handle is attached to the door by a scurvy mandrel ( like ours ) , attach a washer , screw , and cut across to secure and complete the spindle on the interior of the door .
Step 4: Install the Deadbolt
Repeat the procedure above for creating a faceplate indenture if your lock calls for one and your door does not already have one . Fit the door latch bolt into the upper cross bore , making sure the top is facing up ( there is usually an arrow on the latch bolt of lightning to indicate ) . Screw the faceplate in to secure . instal the deadbolt mechanisms on the inside and outside , get sure the key piston chamber part is on the outside of the door . The inside quarter round bout should point up when unlocked and toward the door jamb when lock .
Step 5: Install the Strike Plates
Align the rap plate for the handle against the door jamb and attach with two small screws . check that the bent rim of the ten-strike plateful is facing the direction in which the room access opens . Align the rap plate for the deadbolt , pre - drill your holes , and attach the smash collection plate to the door jamb with two longer screws for extra reenforcement . substitute between the two long screws as you practice them in so that the strike plate does not get push out of alignment .
Test the latch and the bolt to make certain both slide in and out smoothly but not loosely . If the dash wo n’t turn all the way , drill the bolt hole out a small deep until it does . Alternatively , you may need to align the position of the strike plate .
